PlyMatrix
Yellow FRP molded safety grating panels with coarse grit surface - PlyMatrix NZ

FRP Grating NZ

GripLine 38mm fibreglass molded safety grating with a coarse grit top. Won't rust or rot - built for wet, coastal and corrosive sites.

Fibreglass Safety Grating That Won't Rust

GripLine FRP grating is a moulded fibreglass floor grating made for places where steel rusts and timber goes green and slippery. Each panel has a 38 × 38mm open mesh, 38mm deep, so water, mud and debris drop straight through, and a coarse grit surface on top for solid footing in the wet.

It's a go-to for walkways, platforms, dairy sheds, wash-down bays, marinas and industrial sites across New Zealand. The high-visibility yellow marks out walkways and edges, and the panels are light enough to carry and place by hand. We stock three panel sizes - 2405 × 918mm, 2405 × 1220mm and 3660 × 918mm - and deliver nationwide.

Covering a ramp, step or deck rather than spanning an opening? Our FRP anti-slip sheet fixes straight over the existing surface.

FRP Grating Specifications

ProductGripLine FRP molded grating
MaterialFRP (fibreglass reinforced plastic)
Mesh38 × 38mm open mesh
Depth38mm
SurfaceCoarse grit anti-slip top
ColourYellow (high visibility)
Panel 2405×918mm$299.95 - approx. 42kg
Panel 2405×1220mm$399.95 - approx. 55kg
Panel 3660×918mm$449.95 - approx. 64kg
View Prices & Order →

Installation Tips

-Grating needs proper support underneath - tell us your span and use and we'll confirm it suits before you order
-Fix panels down with stainless steel grating clips so they can't shift or lift
-Cut with a diamond or abrasive blade, and wear a dust mask and gloves - FRP dust is an irritant
-Seal cut edges with resin to keep exposed fibres protected and the finish tidy

FRP Grating vs Steel Grating

GripLine FRPGalvanised steel
Rust & corrosionWon't rust, even in salt water, chemicals or effluentRusts once the galvanising is damaged
WeightLight enough for two people to carry and placeHeavy - often needs lifting gear
GripCoarse grit moulded into the top surfaceSerrated bars, slippery once worn or greasy
ElectricalNon-conductiveConductive
Cutting on siteDiamond or abrasive blade, no hot worksGrinding or cutting with hot works

The Product Up Close

Where FRP Grating Is Used

Walkways & Catwalks

Raised walkways, mezzanines, access platforms and catwalks where safe footing matters.

Wash-Down Areas

Water, mud and debris drop straight through the open mesh in wash bays and processing areas.

Marinas & Wharves

Jetties, pontoons and wharf access where steel rusts and timber goes slippery.

Farm & Dairy

Dairy sheds, pits, races and effluent areas that see constant water and corrosive waste.

Industrial & Plant Rooms

Plant rooms, chemical areas, trench and pedestrian pit covers in corrosive environments.

Treatment Plants

Water and wastewater sites where corrosion resistance is a must.

Common Questions

What is FRP grating?
FRP grating is a panel made from fibreglass reinforced plastic - glass fibres set in resin and moulded into an open mesh. It does the same job as steel floor grating but won't rust, is much lighter to handle, and our GripLine panels have a coarse grit top for grip.
What does FRP grating cost in NZ?
GripLine FRP grating panels are $299.95 (2405 × 918mm), $399.95 (2405 × 1220mm) and $449.95 (3660 × 918mm), all including GST. Need a larger quantity for a project? Request a quote.
Is FRP grating slippery when wet?
Our GripLine grating has a coarse grit surface moulded into the top of the bars, and the open 38 × 38mm mesh lets water drain straight through rather than pooling. That's what makes it a popular choice for wet, muddy and wash-down areas.
Is FRP grating strong enough for my job?
GripLine grating is made for foot-traffic areas like walkways, platforms and wash-down zones. How much it carries depends on the span between supports, so send us your span and what it's for and we'll confirm it suits before you order.
Is FRP grating better than steel grating?
For wet, coastal or corrosive sites, usually yes. FRP won't rust, weighs much less than steel so it's easier to install, and it's non-conductive. Steel can still make sense for very high loads or long spans - tell us about your job and we'll give you a straight answer.
Can I cut FRP grating to size?
Yes. Cut it with a diamond or abrasive blade on a grinder or circular saw - no hot works needed. Wear a dust mask, eye protection and gloves, and seal the cut edges with resin.

Other Products

FRP Anti-Slip Sheet NZFormply NZMarine Plywood NZFalcata Plywood NZWhite Oak Plywood NZClearance Deals

Get a Quote - FRP Grating

Tell us your thickness, sheet count, and delivery location and we'll come back with specs and pricing including freight.

Request a Quote →Call 027 358 0315